Baumatic P960SS Pythagora Manual do Utilizador

1el BHG730SS-AUS / BHG750SS-AUS / BHG930SS-AUS Gas hobs

10BHG750SS-AUS Product dimensions: Aperture dimensions: Depth: 500 mm Depth: 480 mm Width: 740 mm Width: 560 mm Height: 35

11BHG930SS-AUS Product dimensions: Aperture dimensions: Depth: 500 mm Depth: 480 mm Width: 860 mm Width: 830 mm Height: 35 mm Product

12Electrical details Rated Voltage: 220 - 240 Vac 50 - 60 Hz Supply Connection: 3 A (double pole switched fused outlet with 3mm contact gap) Max

13Gas hob surface layout BHG730SS-AUS A = 3.80 kW triple crown (wok) burner B = 3.00 kW rapid burner C = 1.75 kW semi-rapid burner D = 1.00 kW au

14o The minimum setting is at the end of the anti-clockwise rotation of the control knob. o All operation positions must be selected between the m

15o The diametre of the bottom of the pan should correspond to that of the burner. o The burner flame must never extend beyond the diametr

16After each use o Remove the pan stands and wipe the appliance over with a soft, damp cloth that has been put into warm soapy water. The cloth sho

17Installation The installation must be carried out by a GASSAFE registered installer, in accordance with the current version of the following. o

18o The edges of the hob must be a minimum distance of 55 mm from a side or rear wall. o 700 mm between the highest point of the hob surface (incl

19BHG750SS-AUS BHG930SS-AUS o Cut a hole in the worktop that corresponds with the relevant drawing for your hob on pa

2User Manual for your Baumatic BHG730SS-AUS 70 cm 5 Burner gas hob BHG750SS-AUS 75 cm 5 Burner gas hob BHG930SS-AUS 90 cm 5 Burner gas hob

20 o Carefully turn the hob upside down and place it on a cushioned mat. o Apply the sealing strip (A) provided around the edge of the ap

21o On the underneath of the hob, adjust the clamps into a position that is suitable for your worktop. Then fully tighten the screws (C) to secure t

22o If it is installed in a room with a volume that exceeds 11m³, then no air vent is required. o If there are any other fuel burning appliances i

23 o Put the gas seal into the elbow. o Fully tighten the elbow and seal onto the gas rail. o The elbow MUST be pointing in a downward

24 o Unscrew the injector (B) and replace it with the stipulated injector for the new gas supply (see table below). GENERAL INJECTORS TABLE K

25Minimum flow adjustment for hob gas taps. All work must be carried out by a GASSAFE registered engineer. IMPORTANT: Always isolate the hob from

26Gas tap maintenance These maintenance operations MUST ONLY be carried out by a GASSAFE registered engineer. IMPORTANT: Before carrying out any ma

27o Reconnect the gas tap, perform a gas soundness test and then reassemble the hob. Electrical connection This appliance must be installed by a q

28My appliance isn’t working correctly IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your m

29 Think Appliances Pty Ltd. 416-424 Barry Rd Coolaroo VIC 3048 Sales Telephone 1300 132 824 Service Telephone 1800 444 357 Website www.think

3

30

31

32

4Contents Environmental note 5 Important safety information 6 – 8 Specifications 9 – 13 BHG730SS-AUS 9 BHG750SS-AUS

5Environmental note o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. o Please discard

6Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before at

7Child Safety o Baumatic strongly recommend that babies and young children are prevented from being near to the appliance and not allowed to touch

8Cleaning o Cleaning of the hob should be carried out on a regular basis. o IMPORTANT: Before attempting to clean the appliance, it should be di

9Specifications BHG730SS-AUS Product dimensions: Aperture dimensions: Depth: 500 mm Depth: 480 mm Width: 685 mm Width: 560 mm